Repairs to uPVC Windows

uPVC is a fantastic choice for modern homes. They are easy to maintain and are durable and long-lasting. Unlike timber and window Doctor aluminium, they don’t get rusty or decay.

It is important to clean and oil UPVC windows and doors on a regular basis. This will reduce unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

If the glass in your window is damaged, it could cause a large deal of damage to your home, making it very dangerous and potentially fatal. It is important to take the time to ensure that you’re doing everything you can to keep your windows in good repair.

Single-pane windows are relatively easy to replace, and they generally fit into frames of the past easily. However If windows with double panes are anchored by internal beading it will be more difficult to remove the old panes and put in new ones. In this case, it is necessary to purchase plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass by yourself. It is also recommended to lay down a dropcloth prior to you begin working on the window doctor panes so that any shards fall on the fabric and not on the floor, where they could be trampled.

After the glass has been removed from the window, it’s best to seal the gap with packaging tape or duct tape to stop water and drafts from getting into the home until a professional is able to come out and fix the window. This will also act as a barrier, deterring any intruders to gain access into your home. If the distance between the window and the door is significant, you may need to consider a security screen that also has windows. This will give you the best of both.

2. Sagging

Upvc windows and doors are a low-cost, durable and energy-efficient alternative to timber windows made of sash. Over time, they can develop a number of problems, including sliding. A sagging window in uPVC can cause issues with light, draughts, and even security. It’s crucial to act when you realize that your uPVC windows are sagging.

To fix a sagging window you can try repositioning the hinges. First, you’ll need to unblock the windows to access the frame. With an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Close your window to check the fit after you’ve relocated your hinges. If you are happy with the fit of the window, window doctor you can tighten screws to keep them in place.

If you are unable to move the hinges, you may have to replace the seal. Rubber seals may dry out and lose their elasticity over time, leading them to loose their elasticity. It is crucial to replace your seal as soon as you can to ensure that your uPVC Window Doctor waterproof and draughtproof.

UPVC handles can also loosen up. Often, this is caused by screws that have come loose over time. However, it could occur because the handle mechanism has been worn out. It’s relatively simple to repair a loose uPVC handle. First, you’ll need to close the window and then perform a test to ensure that it fits. The corners of the sash must align with the casing joint. If it does not then you can use the screwdriver to loosen up the handle. Then, turn the mechanism back into place.

3. Water Leaks

It is important to act if you awake each day to discover mouldy walls and floors that are wet. The leaks of water from windows do can not only cause destruction of your home’s structure but also undermine your efforts to regulate the temperature inside your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame has been damaged or is missing.

This is a relatively easy fix that can be completed by any competent DIYer. Depending on how severe the problem is, the old caulking might need to be removed. It is crucial to remember that when it is about uPVC window repairs, do avoid the temptation to “over-caulk’ as this will only make the area harder to clean and reduce the efficiency of your energy.

Verify that the drainage holes have no debris in them, and also ensure that the sill pan has been angled correctly to drain away from the window. In more serious instances, you might have to consider replacing the window.

Mold spots and rotten sills are other signs of water leakage. The fungus thrives in damp conditions and can spread quickly throughout the house.

If the leakage occurs between the double-glazed glass, it is more likely the problem is with the seal than the frame. A upvc repairs specialist can fix this problem by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

Hinges may be to blame if your uPVC window is difficult to open, or if it opens in an ease. These are easily repaired by any skilled DIYer and are usually completed in a matter of minutes.

Nearly every home in the UK will have either top hung or side hung uPVC windows that are hinged and like any mechanical part they can wear down over time. Changing a window hinge is essentially a simple procedure, but it is easier to do with someone else to help hold the frame up.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. You can do this by looking for the arrow on each hinge, this indicates which way the window should be opened.

Faulty window hinges could be caused by improperly opening the window in a certain way or due to poor installation at the factory. This can often be resolved by sending us a picture on our website. We will be pleased to offer you advice.

It is also crucial to ensure that the hinges are lubricated on a regular basis. This can be accomplished by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window open and close more easily. It also decreases the chance of windows sticking and help prevent corrosion. It is recommended to do this once a year. WD40 and other solvent-based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different factors. First, the hinges due to wear and tear may become displaced, which can cause a gap to form between the sash and the frame. If they’re beyond repair, it might be required to realign them. In addition, the interlock could also become disaligned. It is located on the hinge’s side and might require to be cleaned. In certain instances, it may be necessary to replace them.

The second most frequent reason for draughts is window seals, these are prone to wear or damaged over time and let air escape through these gaps. Replacing these with high-quality weatherstripping is a good way to prevent draughts. Replace the windows made of upvc with low-emissivity lenses. This will help control indoor temperatures and lessen draughts.

Another, and most effective methods to reduce draughts is by using an draught excluder. These are usually fabric tubes which are filled with a sort of filler and can be put on the top of your windowsill. They can keep your home warm by blocking cold air.

With a bit of regular maintenance and repairs windows made of upvc will provide a great level of security and insulation for your home. It is essential to remember that all windows will eventually get worn out and it is cheaper to replace them rather than repair them. If you are having issues with your upvc windows, it is recommended to seek help from a professional as soon as you can.