Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain, durable and long-lasting. As opposed to aluminium and timber they do not corrosion or rot.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will help avoid unnecessary repair costs as well as increase energy efficiency.

1. Broken Glass

The damaged glass in your windows can cause significant damage to your home and even be fatal. It is important to make sure that your windows are in good working order.

For single pane windows, it can be relatively simple to replace windows, and the new one is usually able to fit into the frame that was previously installed easily. However when you have double glazing pane windows that are held in place by internal beading, it will be more difficult to take out the old panes and put in new ones. In this instance it is essential to purchase plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and heavy gloves is essential when you are planning to remove the glass by yourself. You should also lay down a dropcloth prior to you begin working on the window panes, so that any shards fall on the fabric and not on the floor which could cause them to be trampled under.

Once the glass has been removed, it’s a good idea to seal the gap with some clear packaging tape or duct tape to stop water and drafts from getting into the home until a professional comes out and fix the window. This also serves as a barrier to prevent any intruders from making their way into your home. If the distance between the door and the window is substantial, you may want to use a security screen that also has a window. This will give you the best of both.

2. Sagging

Upvc windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber sash windows. However, with time, they may be afflicted by a variety of issues like sliding. A sagging uPVC window could cause issues with light, draughts and even security. If you notice that your uPVC window is beginning to shrink, it’s important to act quickly to stop the issue from becoming worse.

Repositioning the hinges could aid in fixing a window that is sliding. First, you’ll need to unblock the windows so you can get at the frame. With an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you’ve repositioned the hinges, close your window and check for fit. If you are happy with the size of the window, you can tighten screws to hold them in place.

If you are unable to reposition the hinges, you could need to replace the seal. Over time, rubber seals lose their elasticity and become dry and cause their tightness to decrease. If this happens, it’s essential to replace the seal as quickly as you can to ensure that your uPVC windows remain watertight and draught-proof.

uPVC handles could also become loose. The majority of the time this is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has worn out. It’s relatively simple to fix a loose uPVC hand. You’ll first need to close the window and do a test fitting. The corner joints of the sash need to align with the casing joint. If it isn’t, you can make use of a screwdriver to loosen the handle and then turn the mechanism back into the position it was in.

3. Water Leaks

If you wake up to damp floors and mouldy walls every time it rains it is important that you take action. The leaks of water through windows could cause structural damage to your home and hinder your ability to control the temperature in your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

It is a fairly easy fix that can be done by any DIY expert. Depending on the severity of the problem the caulking used previously might need to be removed before a new layer is applied. It is important to remember that when it comes to uPVC window repairs you should not be tempted to apply too much caulk in order to make the area more difficult to clean and could reduce the efficiency of your energy.

Verify that the drainage holes have no debris in them, and also ensure that the sill pan has been properly angled to allow the water to drain from the window. In more severe situations, you may have to replace the window.

Mold spots and rotted sills are other signs of water leakage. This fungus thrives in damp conditions and can spread quickly throughout the home.

It is also important to keep in mind that if the leakage is coming from between the glass of your double glazing glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sagging. It is also possible to be repaired by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open with ease It could be the hinges that are at fault. They can be easily replaced by any competent DIYer and are usually done within a few minutes.

Like all mechanical parts hinges will wear out over time. The process of replacing a hinge on a window is essentially a very simple procedure, but it is easier to do with someone else to assist in holding the frame in place.

Check that the Upvc Repair (Shinhwapack.Co.Kr) hinges open and close in the right direction. This can be done by looking for the arrows on each hinge, this shows which way the window should be opened.

The problem with the hinges on windows can be caused by incorrectly opening the window in a particular manner or because of poor installation at the factory. Sending us a photo via our website will often solve the issue. We are happy to give suggestions.

Regularly lubricating the hinges is essential. This can be done by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can help the window operate and close more smoothly. It can also prevent corrosion and reduce the possibility of sticking. This must be done at a minimum every year. WD40 and other solvent based oils are not recommended because they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by several different things. The hinges, also due to wear and tear can become misaligned, this can cause gaps to develop between the sash and the frame. If they are beyond repair, it might be necessary to have them realigned. The second is the interlock, which is located on the hinge side of the window, may also be misaligned, and again it is feasible to give them a clean but in some cases it might be necessary to have these replaced.

The seals may wear out or get damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping can help stop draughts. Replace the windows made of upvc with low-emissivity lenses. This will help regulate indoor temperatures and lessen draughts.

The final method to cut down on draughts effectively is by using a Draught-exclusion device. These are usually made of fabric tubes filled with a filler, which can be put on top of your window sill. They will help keep cold air out and keep your home warm and cosy!

The windows made of upvc can keep providing excellent insulation and security in your home by performing regular maintenance and repairs. It is important to remember that all windows will eventually get worn out and it could be more cost-effective to replace them instead of fixing them. If you are having issues with your upvc windows, upvc repair it is best to seek professional assistance as soon as you can.