Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are easy to maintain, durable and long-lasting. They don’t get rotten or rusty like timber and aluminum.

It is important to clean and oil UPVC doors and windows regularly. This will help prevent unnecessary repair costs and also improve the efficiency of energy.

1. Broken Glass

The broken glass in your windows can cause significant damage to your home and may even be fatal. It is essential to take the time to make sure that you’re doing everything you can to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace and generally fit into frames of the past easily. However when you have double pane windows that are held in place by internal beading, it’ll be more difficult to take out the existing panes and install new ones. In this case you’ll need to find some plastic spacers to assist the new pane to fit perfectly into the frame of the window.

Wearing protective eyewear and thick gloves is essential when you are planning to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the window panes to ensure that any shards fall onto the fabric, not onto the floor, where they could be trampled.

After the glass has been removed, it’s a good idea to cover the gap with some clear packaging tape or duct tape to stop drafts and water from entering the home until a professional is able to come out and fix the window. This will also act as a barrier, deterring any intruders from getting access to your home. If the gap is large, you might be interested in a security door that has an integrated window as it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber windows made of sash. However, over time, they may be afflicted by a variety of problems including sagging. A sagging uPVC window can cause issues with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it’s important to act quickly to prevent the problem from getting worse.

Repositioning the hinges can aid in fixing a window that is sagging. You’ll first need to open the windows to access the frame. You can then unscrew both the hinges on the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you’ve adjusted the hinges, close your window repairs near me and check for an appropriate fit. If you’re satisfied with the fit, Window repairs tighten the screws until they stay in the right place.

If you cannot reposition the hinges, you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, which causes them to lose their tightness. If this happens, it’s essential to replace the seal as fast as possible to ensure your uPVC windows are watertight and secure from draughts.

UPVC handles can also become loose. Often this is due to screws that have come loose over time. However, it can occur because the handle mechanism has worn out. Luckily, it’s not difficult to fix the handle of a window that is loose yourself. First, you’ll need to close the window and then perform an initial fitting. The joint at the corners of the sash must align with the joint on the casing. If it doesn’t, you can use a screwdriver or a wrench to loosen the handle, and then turn the mechanism back into position.

3. Water Leaks

If you’re waking up to wet floors and mouldy walls each time it rains it’s crucial to take action. Water leaks from windows are not just a cause for degrading of the structure of your home but also hamper your efforts to control the temperature in your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix and should be undertaken by any DIY expert. Depending on the severity of the problem the caulking that was used up may require removal before a new layer of caulk can be applied. It is crucial to remember that when it is about uPVC window repairs, do avoid the temptation to “over-caulk and then make the area more difficult to clean and can reduce the efficiency of your energy.

Make sure that the drainage holes do not have debris inside them and that the sill pan is properly angled to drain away from the window. In more serious instances, you may need to replace the window.

Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window. The fungus thrives in humid conditions and can propagate quickly throughout the house.

It is also important to note that if the leakage originates from the glass in your double glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or if it opens in an ease. They can be easily repaired by any DIYer who is skilled and can be completed in a matter of minutes.

Like any mechanical component hinges are prone to wear out over time. It’s easy to change a window hinge but it’s much easier if someone helps you to hold the frame.

It is also worth checking that the uPVC hinges are opened and closed in the right direction. Check for the arrows on each hinge to determine which way the window should be opened.

The issue can be caused either by opening the window improperly or by a poor installation in the factory. This issue can be fixed by sending us a photograph on our website. We will be pleased to offer you suggestions.

It is also crucial to ensure that the hinges are lubricated regularly. This can be done by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regularly lubrication makes the window easier to open and close. It can also lower the possibility of a window sticking and prevent corrosion. It is recommended to do this at least once a year. WD40 or other solvent-based oils should not be used since they could damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by different things. The hinges can also become disaligned as a result of wear, which can cause gaps between the frame and sash. If they’re beyond repair, it could be necessary to get them re-aligned. The interlock, which is located on the hinge side of the window, may be misaligned. Again, it’s possible to give them a clean but in some instances it could be necessary to get them replaced.

These seals are susceptible to wear and tear or be damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with glass that is low-emissivity, this will help in regulating indoor temperatures, and also lessen the possibility of draughts.

Another method of reducing draughts effectively is by using a Draught-excluder. These are usually fabric tubes filled with a filler which can be placed over your window sill. These will help to block out cold air and keep your home warm and cosy!

The windows made of upvc can keep providing excellent insulation and security to your home by performing regular maintenance and repairs. It is crucial to recognise that all windows have a lifespan and eventually, they will reach the point when it’s more efficient to replace them than repair them. If you have any problems with your Upvc window, it’s best to consult an expert as soon as you can.