Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window or door mechanism not working properly? Perhaps the door or window handles aren’t able to connect properly or are hard to use.

You’ll be wasting energy if your double-glazed doors don’t function properly. This increases the risk of burglary. Owen the Locksmith will be able to repair your door lock at reasonable costs.

Snapped Key

If a key breaks inside a lock, it can be incredibly annoying. It could also be an issue for security, since the door may not lock and could leave you vulnerable to burglars. There are a couple of quick solutions you can use to resolve the issue and make your door functional again.

Remember to remain calm. If you panic, you could end up pushing the damaged key piece further into the lock.

Spray WD-40 or another penetrating lubricant, into the lock. This will assist the broken piece to come out more easily. You can also use a screwdriver to break off any pieces that are stuck. If you happen to have a small piece of the key that is hanging out it, you can make use of a paperclip, or any other metal object with a thin surface to grab it and pull it out. Both methods work well, but be very careful not to push the damaged piece of the key further into the keyway.

Some paperclips have grooved edges that could serve as hook extractors and some Jigsaw blades can also be used for this purpose. If you don’t have any of these, you can bend a hook with needle-nosed pliers. You can also use a pair tweezers to grab and remove the last piece of broken keys.

If you cannot remove the broken piece of key, use a lock deicer. It is available in most hardware stores and is used to freeze any moisture present in the lock.

If none of these tricks are working, it might be the time to contact a locksmith. Fitlocks experts can quickly fix problems such as broken handles and broken keys with uPVC locks and door mechanisms. They can also reconfigure double glazing door mechanisms to ensure that they are easier to use. Request a repair for your double glazing repair glazing with us online or give us a call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose an extremely risky security issue. A professional locksmith is able to fix the cylinder. Locksmiths will need to tap the cylinder in order to fix it. They can do this using the hammer or any other tools, but the most effective method is to use a long match or a piece of wire. Place the match or wire’s end close to the keyway. The locksmith will then hit the lock to crack it. This is far better than using a heavy hammer that can cause damage to the lock.

Overheating is the most common reason behind cylinder heads cracking. This can happen when the cylinder block and head are made of various metals, like cast iron and aluminum. When the different metals heat up and cool down at different rates, it can create hotspots locally that expand faster than the rest of the cylinder head, leading to cracks.

Corrosion can be a cause of fractures in cylinders. If the head and block of a cylinder are not maintained in a timely manner they may corrosion or rust, which can cause them to expand faster than anticipated. This could lead to cracks over time.

If your uPVC window or door lock is rigid and requires a lot more pressure to turn, it could be due to a variety of reasons. A faulty locking mechanism, misalignment, or a worn handle are common causes of this problem.

This is a straightforward and affordable fix that the majority of homeowners with double glazing can perform. A professional locksmith should be able to solve this problem within an hour of arriving at your property. Depending on your needs, they can replace the locking mechanism, change the window handles, and change the gearboxes. A professional locksmith can always advise you on the most cost-effective solutions for your home. They may recommend upgrading to 3 Star TS007 Euro Cylinders, which give you an extra layer of protection against burglars. This is a small price to pay for the security that comes from knowing that your uPVC doors are secure.

Broken Handle

Window handle locks have complex mechanisms that deteriorate with age and use, so it’s no surprise that they can break. It can be difficult to determine the reason behind the broken window handle lock and fix it correctly.

The issue could be in the internal locking mechanism or the latch, Window doctor Near me fixing your broken handle will improve your uPVC double glazing door’s security and allow you stop the draughts. If you do not repair or replace your handle can be expensive and could harm the door’s frame as well as lock, so it’s worth taking some time to make sure you do it right.

Screwdriver Open the window doctor near me and the screw loose, loosen the handle. This should be located on the inside of the back plate, and is normally covered by an aesthetically pleasing cover for the screw reasons. Be sure not to lose any internal parts within the handle, like the plates or levers that are on either side of the spindle. Keep them in the same arrangement so that it is simpler to replace them in the event of a need.

Then, with an additional screwdriver loosen the screw that connects the handle to the spindle in the back. Once the screw is removed, you should be able to pull the handle off and pull out the broken spindle. Replace it with a brand new spindle, making sure it’s the same length (you can purchase them online or at hardware stores). Screw it into place. Do not overtighten the screw as this can cause damage to the handle and window frame.

Check that the new handle is fitted after which you can close and test the handle. It is likely that it will operate smoothly and you’ll be able to unlock your window.

Be sure to double-check that your uPVC window is closing properly when you’re working with the handle. If they’re not then you may experience damp and draughts inside your home as and also affecting the efficiency of your home’s energy usage. Core Sash Windows is a local window company that can alter the hinges on the window frames to ensure they close correctly.

Broken Spindle

It is quite common that the spindle in the handle breaks, rather than the handle itself. This is particularly typical in uPVC tilt and window doctor Near me turn windows. These windows require a handle which is a lock mechanism that is located in the window frame. The handle is attached to a central rod which activates locks that are shaped like mushrooms and lock into the window frame keep. If the dead latch mechanism fails to open when the handle is turned, it is likely that the spindle has broken This can be a very frustrating issue.

Luckily, there are steps that can be taken to rectify this issue. A professional locksmith will be able to quickly and effectively fix this issue. They will be able to remove the window handle using a tool to remove the wheel portion of the mechanism that is where the spindle is. This is done without damage to the handle or window doctor Near me frame.

After the wheel has been removed, the technician will inspect the spindle to determine what caused it to break. This involves breaking down the spindle into its individual components and carefully observing their general condition as well as any particular areas of damage or excessive wear. This procedure is typically performed by technicians in a clean environment.

The next step is to clean the damaged spindle. This will help get rid of any debris or dirt that might be preventing it from working normally. Following this the spindle is cleaned, it can be repaired or replaced. If it’s being replaced, the technician can take an identical dowel size to the original and drill mating holes in both pieces of the spindle. This will ensure that the new spindle has a precise fit with the handle.

If the spindle is damaged and cannot be repaired it may require replacement. Home centres sell generic substitutes, but if your window design is unusual you’ll require contacting a cabinet maker or woodworker who can recreate the exact component. Once the new spindle is in place it can be positioned to the handle by line up the screw holes in the handle and the frame existing screws. Once the handle is securely seated, you can operate your uPVC windows.