upvc window handle replacement [http://www.smuniverse.com/bbs/board.Php?bo_table=smu4_3_eng&Wr_Id=48835]
It’s easy to replace a broken window handle with the proper tools. It’s important to know what kind of handle you have and its spindle size before purchasing a replacement.
Older uPVC window handles have a spur which protrudes and locks on the cockspur wedge striker. They can be left or right-handed and need to match when replacing.
What type of lock or handle do you have? I have
There are many upvc window locks and handles each with their distinct advantages and functions. The type of handle you have will determine how easy it is to open your windows and if the locking mechanism works as intended. With time and regular use, window handles made of upvc may become damaged or worn out, making them less secure and efficient. In some instances they might even fall off completely. If you find that your window handles have fallen off, it’s essential to fix them as soon as possible. This will help prevent burglaries, and keep your house secure.
It’s an easy task that virtually anyone can perform. You will need some basic tools, but with proper knowledge, it’s a straightforward process that should take only a couple of minutes. You will need to know the kind of handle or lock that you have on your window. This will allow you to choose the correct replacement window handle.
Inline Espagnolette Handles
They are usually found on the side of the window. They have a flat design and UPVC Window Handle Replacement feature an opening that is connected to the locking mechanism on the window frame when it is turned. Inline upvc handles have spindles that run through the centre of the handle and then into the window frame to operate the latch.
Cockspur Handles
These handles are usually found on older uPVC window frames. They have a distinctive, hook-shaped design. Cockspur handles are secured to the frame of the window by one screw, and are less secure than other kinds of window handle.
Handles that turn and tilt
The tilt and UPVC Window Handle Replacement turn handles differ from other handles made of upvc in that they can be rotated to open the window and then tilted into the window to ventilate. They typically have a 7mm spindle on the side of the handle. They are available in left and right-handed versions.
It is important to measure the spindle’s size prior to purchasing a new upvc handles. Not all of them are the exact same size. Drop something into the middle of the hole to measure the length. This is the largest spindle size that will fit your windows.
What is the spindle?
uPVC window handles function in a similar way as doors, with the user turning the handle to open a latch inside the frame. This unlocks the window so it can be closed and opened. The handles can become damaged, especially if used frequently or exposed to harsh conditions. This could mean that you have to replace your uPVC handles on windows since they might not operate the window properly for a long time.
There are a variety of uPVC handles to choose from, comprising Espag, Cockspur and Spaded handle options. They are designed in a variety ways to fit into uPVC frames. Each handle style uses an individual spindle to lock the window mechanism. This is why it is important to know what type of handle you have on your uPVC window so you can get the correct replacement.
You can determine the type of uPVC handle you are using by looking at the base section of your handle. There should be a “snap in cover’ over one screw that holds the handle’s base in the correct position. After removing this you will be able to see the screw that holds the base of the handle in position. After both screws have been removed then you should be able to remove the handle from the uPVC.
Once you have removed your uPVC window handle, you will need to carefully unscrew the spindle that was previously attached to the locking mechanism. Make note of the length of the spindle since you will need to ensure that you buy a replacement that has the same length as the original handle and locking mechanism.
The primary issue with uPVC window handle problems is that the spindle becomes worn out and cannot longer operate the locking mechanism. This could be due to corrosion, damage caused by continuous use, or even a loosening locking mechanism. If this occurs, you will have to replace both the window handle and locking mechanism in order to restore the full functionality of your uPVC Windows.
How do I take off the old handle?
Window handles can be damaged or even broken over the course of time. It is important to repair them as quickly a possible to ensure your security. It is good to know that replacing a worn or damaged handle is a simple task that can be accomplished in less than a minute and doesn’t require any specialized tools.
The first step in removing the handle that was previously used is to take off the screw located on the top of the base of the handle. Once this is removed the handle can be removed from the base. Another screw will be located at the base of the handle. It can also be removed. After these two screws have been removed, the handle will be detached from the base of the window.
Once the old handle is removed, you can take the new handle and line up the fixing holes with the holes that are currently in the window frame. If there is a cap or sticker on the new handle, take it off it if required and screw the handle in place. It is important to check that the handle works once it is put in place. Turn the handle around and make sure the lock mechanism is in place.
Espag handles feature spindles that protrude from the handle and slots into the multipoint locking mechanism that is on the frame of the window. Cadenza windows come with a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hang over the frame that surrounds the window or the transom crossmember of the bar.
Once you have the new handle in place, you can insert the spindle into the lock in the window and then tighten it down. Replace the snap-in cover and screw cap (if applicable) once the handle is securely fixed. The handle is now ready for use by opening and closing the window a few times to check that it functions well and securely.
How do I install the new handle?
The process of changing your window handle made of uPVC isn’t a big deal and the process is actually very simple. You only need an screwdriver and a little bit of patience. The first thing to do is ensure that the handle you have previously used is not locked and then remove any screws that are visible, you can also replace these with screw caps if needed. After removing the handle you will need to note the length of spindle that extends from the back. This is vital as it will determine what type of handle you need to purchase.
Espagnolette handles are the most commonly used type of handle used on uPVC windows. They feature a spindle that is inserted into the handle and operates an internal locking mechanism within the window frame. The handle opens the latch and allows the window to open. In regular use and time, espagnolette handles may be damaged.
Cadenza handles are a form of uPVC handle that is commonly used with tilt and turn windows. They feature a protruding knife that is operated by a multi-point locking mechanism inside the window. They are more secure than an espagnolette handles because they are able to open from the inside. You can replace them with the same procedure as you would do for handles made of espagnolette however, ensure that the new handle is not angled and flat.
Once you have decided on the right handle for you, you can simply line up the new handle to the existing screw holes, and then screw it into place. Then, put the screw covers back on and verify that the new handle is working properly. This is done by moving the handle from the locked position to the unlocked and vice versa a few times. It is possible to contact an expert to see whether you can solve any issues. They can provide advice on how to resolve the issue in a quick and effective manner.